Info wrapping film / adhesive film / window film & artificial leather.. frequently asked questions..
How thick is the wrapping film / how is it processed / how is it shipped?
- The wrapping foil can be glued dry. Thickness approx. 70/130 µm (micron) = 0.07/0.13 mm
- Adhesive layer: Solvent acrylic, permanent. Backing paper: Double-sided PE coated paper
- Recommended application temperature: +16°C minimum (environment and substrate!)
- The self-adhesive film is 152CM wide and has air channels to remove air bubbles.
- Can be stretched using a hair dryer, use it from a distance (25cm) due to the heat effect.
- Not applied properly? Gently pull off the wrap foil and blow-dry carefully until it is properly applied
- Suitable for wrapping car / scooter / bus / kitchen / desk / table / cupboard / shelf etc.
- The wrapping foil can be ordered per meter/unit and is 152 cm wide (quantity 1 = 1 linear meter)
- Orders of multiple meters/units are always shipped in 1 length and rolled up!
- Delivered products may have a slight deviation in color compared to the product shown
- Depending on the screen and system settings concerned, if in doubt please contact us
- Due to the width of the wrapping foils (152cm), they are sent via DPD or Post NL
- Before applying the wrapping foil, it must be thoroughly degreased with water-based or alcohol-based degreasers.
- Ethyl alcohol and isopropanol are both alcohols that can be used for cleaning and degreasing in the correct manner.
- Both are readily soluble in water and can be used as a versatile solvent or degreaser.
- The alcohol evaporates quite quickly and therefore leaves little to no residue, advice: use minimal dosage.
- During application, it is recommended NEVER to blow-dry for too long in one spot and AT LEAST from a distance of 25cm.
- The adhesive layer can be blown to pieces if this is not done correctly and will then no longer adhere.
- Avoid unnecessary contact with the adhesive layer and try to stretch/deform the wrapping film as little as possible.
What do the terms EM - 2D - 3D HQ - 4D and 5D Carbon mean?
-
EM : Own Brand Foils
- 2D : printed, laminate layer, rectangular blocks.
-
3D : tactile relief, rectangular blocks with stripes, small pattern.
-
3D HQ : tactile relief, rectangular blocks with stripes, large pattern.
-
4D : slightly tactile relief, rectangular blocks with half circles.
-
5D : same as 3D plus a glossy laminate layer.
Please note : the foil can be ordered from 1 meter/unit and is 152 cm wide (quantity 1 = 1 linear meter)
Orders of multiple meters/units are always shipped in 1 length and rolled up!
Due to the width of the wrapping foils (152cm), they are sent via DPD or PostNL
Please note : delivered products may have a slight deviation in colour compared to the product shown in our webshop, depending on the screen used and system settings. Each screen displays colours differently, which may cause a difference. Please take this into account.
What tools do I need to apply adhesive and/or window film?
- pen
- ruler
- pair of scissors
- a clean cloth
- sharp (stanley/snap-off) knife
Info adhesive film & window film..
On which surfaces and substrates can I apply adhesive film and/or window film?
The foil can be applied to almost all clean (dust and grease free) smooth surfaces such as windows, tables, doors, cabinets. When the foil is applied to untreated wood, we recommend applying a primer/sealer beforehand, to ensure adhesion.
How do I cut and apply the adhesive film to the surface, for example a cupboard?
Place the foil down with the back of the paper facing up. Use the measurements on the back to measure and then draw the size. Leave a margin of approximately 4mm on each side, this extra margin can easily be cut away after the foil has been applied. The foil can now be roughly cut/cut to the desired size. Remove the protective foil on the back. Apply the foil (dry is preferred, on certain objects the foil can also be applied damp) to the object and smooth it with a spatula or soft cloth. The previously applied and excess 4mm margin can be cut away along the edges.
How do I cut and apply the window film to the surface, for example a window?
Measure the surface and make sure that you stay 2mm inside the window frame, excess moisture can escape here later. Make sure that the surface is dust and grease free. Now spray the surface with sufficient water, this may contain a drop of washing-up liquid. The more water, the better and easier the application. Remove the protective film on the back. Apply the pre-cut film to the damp window. Position the film and slide the moisture under the film to the outside of the window with a window squeegee or spatula, so that the moisture can escape here. The film then needs time to dry.
How do I remove any air bubbles under the foil?
If there are air bubbles under the foil, possibly because the foil has not been applied sufficiently:
- Carefully loosen the foil on 1 side until the air bubble is reached, use a spatula or cloth to smooth the air to the outside until it disappears or,
- If the air bubble is close to the edges, gently push it out with a spatula (do not press too hard on the foil) or,
- Carefully pierce the foil where the air bubble is with a sharp needle, so that air and/or moisture can escape from here.
How can I apply foil to/around rounded corners and/or curved objects?
Heat the foil with a hair dryer, be careful: use the first setting so that the foil does not get too hot and can burn. Then apply the foil to the object while it is warm and iron the foil around the corners and edges. Be careful not to pull too hard on the foil so that it does not tear.
How thick is self-adhesive / static cling window / adhesive film & self-adhesive wrap film?
- All our self-adhesive window films have a thickness of approximately 110 - 130 µm / micron (0.11 - 0.13mm)
- All our static cling window films have a thickness of approximately 110 - 130 µm / micron (0.11 - 0.13mm)
- All our static window films have a thickness of approximately 180 - 250 µm / micron (0.18 - 0.25mm)
- All self-adhesive wrapping films have a thickness of and between approx. 70 - 130 µm / micron (0.07 - 0.13 mm)
Can I use the film in damp areas and/or on the outside of windows?
Yes, the film can be used in damp areas, provided it is applied correctly. The film may not have any openings on the sides where moisture can possibly enter. For extra security, the edges can be additionally sealed / sealed. It is not recommended to use the window film outside. The adhesive & window films offered by us are produced with the intention of indoor use.
Except for wrapping films, these are used outdoors or recommended for applications on cars, of course this type of film can also be used and processed indoors for sticking on: kitchens / cabinets / window sills / panels etc.
Is the window/adhesive film resistant to high temperatures?
For short periods of exposure to heat, the film can withstand temperatures up to 75°C.
Does the foil have a fire standard or is it fire retardant?
The foil is produced on the basis of PVC and is therefore not fire retardant, like other PVC products. The foil has no fire standard.
Where are the films produced?
The films we supply are largely produced in the EU, films that are not available in the EU may have been produced in PRC.
What are the components of the window and/or adhesive film and are they environmentally friendly?
- The foil is made of PVC, is solvent-free and free of heavy metals
- The glue consists of water-based acrylic and is also solvent-free.
- The foil is printed with water-based ink
- The back paper is 62 g/m² incl. a cm scale, printed with water-based ink
- PVC is a thermoplastic that is formed after polymerization of the monomer (VCM)
- Since 2006, PVC contains organically based stabilizers, this is mandatory by the government
- All additives comply with the European directive; REACH standard / DIN EN ISO 105-B02 / X12.
- And also to the internationally recognized guideline and standard: ISO 9001:2000 - ISO/TS 16949:2002 - ISO 14001
See also our page specifications (in our other B2B/B2C webshop) wrapfoliekopen.nl/specifications/
How do I remove window and/or adhesive film?
Start by gently loosening a corner, like when removing a sticker. This process is easier by slightly heating the foil with a hair dryer, for example, on the lowest setting! When the foil is heated, it will be easier to release from the surface.
Any residue/residual glue left on the window can be removed with warm water or by using a sticker remover.
Info Noblessa© artificial leather..
A new look for your home.. Make old new!
With Noblessa© artificial leather, you can easily enhance furniture without much expense.
What is needed for this, a little skill and tools. Then the transformation succeeds in a few steps.
The synthetic leather is easy to clean and washable, is wear-resistant/durable and flexible. And has a high tensile strength.
Noblessa© artificial leather is used for upholstery and upholstery of chairs, sofas and/or headboards of beds.
Tools required : Stapler / Staples / Ruler / Stanley knife / Marker or pen
Preparation : Carefully remove the old fabric from the frame. Place the old fabric on the noblessa© Leatherette. Then cut the Leatherette to size, leaving plenty of room.
1. First step : Place the chair seat on the Faux Leather. The edges should overhang equally. Staple each side in the middle to the bottom of the seat
2. Staple the artificial leather : When processing, make sure that the artificial leather is pulled tight each time and remains under tension. Staple the sides to the bottom of the seat. Work from the middle to the corners. Wait with stapling the corners. Use as many staples as possible and staple the artificial leather as well as possible.
3. Cutting the artificial leather : After the artificial leather has been stapled on all four sides, the overlapping leather can be cut off, except for the corners, up to the staples.
4. Folding corners : Pull the Faux Leather tight and under tension around the corners, towards the bottom of the seat. Staple these parts under the seat.
5. Final step : Carefully and carefully cut off the overlapping Faux Leather in the corners, up to the staples.
Tip:
When covering and upholstery thick foam, e.g. headboards of a bed, it is important to fold the artificial leather generously over and around the corners.
Our advice is to use the artificial leather indoors, but outdoors is of course also possible, but no guarantees can be given in this regard.
Good luck and have fun with this fun transformation.. Make old new!
Regarding UV and light resistance, see features below.
- The artificial leather has good resistance to fading due to light and/or UV
- Test method according to DIN EN ISO 105-BO2, classification 5 → good resistance to light and/or UV
- Test results are displayed in 8 steps..
- Where 8 means very high light resistance and 1 means very low light resistance
- In general, every type of substance fades to a greater or lesser extent when exposed to direct and/or indirect light.
- Our experience is that the artificial leather retains its colour well in practice and when used indoors and does not or hardly discolour.
Technical data Noblessa© Faux leather:
- Grammage: approx. 630 g/m²
- Total thickness: approx. 1.1 mm
- Abrasion resistance / Martindale: Test method according to DIN 12947-2 50,000 Tours iO
- Lightfastness: Test method according to DIN and ISO 105-B02; Level 5
Good luck, and we're happy to answer any questions you may have.
By message or email: info@colletti.nl
HOME
